Sign in
Explore Guest Blogging Opportunities at Wakamoto Journal
Explore Guest Blogging Opportunities at Wakamoto Journal
Your Position: Home - Wire Mesh - The Ultimate Buyer's Guide for Purchasing ornamental metal gates
Guest Posts

The Ultimate Buyer's Guide for Purchasing ornamental metal gates

Sep. 02, 2024

Buyer's Guide to Choosing A Cantilever Sliding Gate

Buyer&#;s Guide to Choosing A Cantilever Sliding Gate

America&#;s Gate Company offers a wide selection of ready-made and custom fabricated gates, no matter the applications. As the gate division of The American Fence Company, America&#;s Gate Company has over 55 years of experience in gate design, fabrication and installation. With either fabrication facilities and a large team of certified welders and computer-aided designers, your gate will be fabricated to match your unique requests.

Zishen are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

The goal of this article is to assist you in selecting your cantilever slide gate for your home, business or job site. We will review the different types of cantilever gates and all the factors that weigh into this decision. If you are looking for a gate, but aren&#;t sure that cantilever gates are your best option, check out the America&#;s Gate Company guide to choosing your gate.

Cantilever Slide Gates

One of the types of slide gates is a cantilever gate. Cantilever gates are unique because they don&#;t roll on the ground. The gate is supported by a series of trucks (rollers) attached to two support posts on one side of the opening. The distance between these posts is usually equal to half the length of the gate opening. Two factors you should consider first when selecting a cantilever gate:

  • Elevations &#; Cantilever sliding gates must be installed level. This is both for the most recent standards and codes and for practical safety reasons. A cantilever gate installed that isn&#;t level will roll downhill. Review the elevations of the finished grade underneath the entire travel of the gate from the nose of the gate in the closed position, to the back of the tail in the full-open position. The highest elevation will be your benchmark. The gate should be set at least two inches above this elevation. If the highest elevation of the gate is at the tail section and the elevation slopes down through the opening, this will cause a considerable gap under the gate at the opening.
  • Storage for the gate &#; Cantilever slide gates are approximately 50% larger than the gate opening. So, a 20&#; opening would require a 30&#; overall gate leaf. This additional 10&#; of gate is called the &#;counter balance&#; and considered the tail of the gate. Evaluate your site to determine if you have enough room to accommodate the gate opening and the gate storage.

Cantilever Gate Infill Type

If there are no issues of elevation or room for gate storage on your property, you should now consider the various performance and design factors of selecting a cantilever sliding gate. The first factor to consider is the type of infill, which will dictate the design and materials of the gate. Though these categories are very broad, selecting one will better help designers and contractors understand your vision. America&#;s Gate Company supplies CAD drawings and specifications for any of the styles of infill mentioned below.

Ornamental Cantilever Gate

An ornamental cantilever gate will incorporate vertical pickets into the gate frame at the opening. The size of these pickets is generally ¾&#; to 1&#;. In accordance with ASTM A and UL325, the pickets should be spaced so you do not have a gap greater than 2 ¼&#; throughout the entire length of the gate, in case it ever would be automated. Pickets should not protrude through the bottom rail of the cantilever gate and the bottom rail should be flush. Pickets may extend above the top rail of the gate and be adorned with an ornate cap. Ornamental cantilever gates may also include other adornments throughout the infill area of the gate.

Decorative Cantilever Gate

Decorative ornamental cantilever gates include an infill material that is typically highly decorative but not of a picket design. The gate infill material may include the use of a solid slating, louvers, perforated metal, etc. If it is going to be automated, decorative cantilever sliding gates also require gaps no larger than 2 ¼&#; throughout the gate. Decorative cantilever gates are classified separate from ornamental slide gates because the mix of infill materials typically causes both wind load and weight concerns for the gate. However, if either of these situations are a potential concern or hazard  for your project, ornamental cantilever slide gates with picket infill do not suffer wind and weight distress.

Chain Link Cantilever Gate

This category of cantilever gates is the most common and widely used type of cantilever slide gate. If you have an automated chain link cantilever gate, it should not include gaps greater than 2 ¼&#; throughout. To accomplish this, chain link fabric can be extended throughout the entire length of the gate. Chain link cantilever gates typically do not have any weight or wind loading concerns as the chain link fabric is 98% open.

High Security Cantilever Gate

High security cantilever slide gates include non-climbable or solid surface infill materials. These gates are also kept tight to the ground and are generally very tall. These features help to keep unauthorized personnel out and keep your property secure. Some concerns for high security cantilever slide gates are their wind loading and weight. The solid surfacing or tight non-climbable wire mesh is much heavier and more dense than standard chain link fabric. Designers should pay special attention to site elevations specific to the path of these cantilever gates. Elevation changes in the overall travel of the gate may result in gaps under the gate when installed level.

Gate Opening

Once you have selected the overall use and material of the gate, you now want to consider performance factors and structural elements that are directly affected by this design. The opening width of the gate is the single most important detail of the overall gate design. The opening width of the gate, along with the selected infill materials, will greatly influence the type of structural gate frame needed to support the gate for both weight and wind loading.

Single Track Gates

Gates with an opening of less than 27&#; with standard chain link or ornamental picket infill may use a single track. Aluminum cantilever slide gates with an opening of 27&#; or less incorporate a single track into the aluminum structure of the gate, and are the most economical cantilever option. The track is at the top of the gate and offset to one side to form one of the following conditions:

  • Inline cantilever gates place the track to the face of the gate. The gate support posts that support the trucks are set in the fence line with the gate behind the fence line.
  • Offset cantilever gates place the track to the backside of the gate. This puts the cantilever gate support posts behind the gate. The support posts are both offset and independent of the fence line.
  • Single track cantilever gates are typically used with openings less than 27&#; and with standard chain link infill materials.

Double Track Gates

Double track gates are generally chain link and ornamental cantilever gates with openings of 27&#; or more, or decorative gates with solid or semi-solid infill. They incorporate a double track into the aluminum structure of the gate. There is one track on each side of the gate at the top.

This application requires four gate support posts with two on each side to support the rollers. In addition to having two tracks, roller and support posts combine to support the weight of the gate, as a double track cantilever gate has a much wider horizontal structural profile. This wider profile provides greater support for wind loading.

A standard single track cantilever gate has a horizontal profile of approximately of 5&#;. A double track cantilever gate has a horizontal profile of double a single-track gate.

Modified Double Track Gates

A standard double track gate can be modified for larger openings or larger decorative gates with solid or semi-solid infill. The horizontal profile of the gate is widened by implementing structural profiles into the upper track assembly to spread the tracks apart, and by providing a wider lower guide track.

A standard width for a double track cantilever gate is approximately 10&#; wide at the upper track assembly. Modified double track gates may range from 12&#; &#; 16&#; at the upper track assembly. The lower guide track is typically 5&#; wide for double track gates. It may be widened up to 8&#;. The purpose of these wider upper and lower members of the gate is to provide greater structural support for wind loading on the cantilever gate.

Modified double track cantilever gates do not necessarily include standard designs. These modifications should be engineered by the gate fabricator and implemented accordingly based on the design of the gate.

Box Cantilever Gates

The design of box framed cantilever gates is rooted in the simple design elements of a standard truss system. A box cantilever gate is basically two identical cantilever gates, spaced approximately 24&#; apart. A series of truss members are placed between the two gate panels to form a pattern of diagonal trusses.

A box cantilever gate uses four truss systems like a steel building ceiling truss to create a very rigid overall framework under a heavy load and/or high winds. Box framed cantilever gates are typically reserved for very large openings in excess of 50&#; or solid materials placed across the gate opening.

Gate Height

When it comes to the structural design, the gate height may not be as important as the overall gate opening, but it does have a significant impact on certain design criteria. Wind loading is going to be the most significant factor. The taller the gate, the more the wind load is going to bear on the face of the gate. The performance criteria you need to consider:

Infill Materials

Using solid infill materials on the face of gates taller than 6&#; may require re-evaluating the gate frame design. Regardless if it has a single or double track, the impacts of high winds on a solid surface gate face may be destructive. No matter the gate&#;s opening width, a box cantilever gate should be considered.

To reduce wind loading, consider using a perforated sheet, welded wire mesh or allowing an opening in the face of the gate to relieve the pressure. An example of this would be a decorative cut-out from weather sheet metal (e.g. mountain scene, trees, etc.) where an opening is left for pressure release.

Gate Support Posts and Footings

Your cantilever gate post selection and footing size should be appropriate to the overall weight and size of your gate, however, the taller your gate, the greater the load you are placing on these posts. This is because you are allowing any wind load to have more leverage with taller gate posts.

Most standard height cantilever gates, 8&#; tall or less, use 4&#; O.D. ASTM gate posts regardless of the overall length of the gate. This is because the majority of the load being placed on the gate posts is not a cantilevered load but a load that is pulling and pushing, stressing the tensile strength of the posts which is in the tens of thousands of pounds. Taller gates, 10&#; or taller, may use 6-5/8&#; O.D. schedule 40 posts to accommodate both the stress on the tensile strength and cantilevered load placed on the gate.

Cantilever Gate Hardware

Gate hardware for cantilever gates is fairly standard regardless of the weight, length and width of the gate. The selection of hardware is more specific if the gate is an enclosed aluminum track gate or a steel tubular gate with external rollers. You should consider using non-standard, heavy-duty gate hardware once the gate begins to exceed 2,000 pounds. Specifically, the rollers or trucks that support the weight of the gate while allowing it to roll freely. Your gate designer should appropriately match the gate hardware, trucks, rollers, and guides, to the type, size and weight of the gate.

Gate Weight

Rarely do we see cantilever gates that weigh more than 2,000 pounds. Non-typical, heavier gates are the result of openings longer than 30&#; or heavy solid infill materials in the opening section of the gate used for decorative reasons. To accommodate these non-typical heavy gates, consideration should be given to the following:

Single or Double Tracks

Aluminum enclosed track gates offer both single and double track options with one track on each side of the gate. Not only is this double track design a good choice for longer gates but also for heavier gates as it spreads the load of the gate on four truck assemblies versus two on a standard single-track design. Openings exceeding 27&#; in width usually require double track gates.

Gate Truss Design

Cantilever gates use a standard diagonal truss design throughout the length of the gate to support the cantilevered load of the gate. Building and bridge truss designs are very similar as the diagonal members are placed in-between vertical members.

There are a top and bottom continuous horizontal support track where the vertical members connect. This pattern of horizontal, vertical and diagonal supports creates a series of connected squares. The diagonal members prevent the squares from being pulled out-of-square by connecting opposite corners together. The only way the square(s) can be pulled out-of-plumb is for the diagonal member to be compressed or stretched.

Related links:
Exploring the Benefits and Applications of 316 Stainless Steel ...

Are you interested in learning more about ornamental metal gates? Contact us today to secure an expert consultation!

This is where the tensile strength of metals comes into play. The tensile strength of most respective metals is in the tens of thousands, meaning it would take thousands of pounds to pull the diagonal truss apart. This is where a typical truss gets its structural strength.

If the diagonal members were removed from a gate&#;s framework, the squares would quickly bow under gravity. This is significant considering the cantilevered load for most respective metals is only in the hundreds of pounds.

Cantilever Strength and Support

A cantilever gate&#;s truss design can be improved to support longer and heavier gates. Most cantilever gate designs use a standard principle: The length of the gate&#;s vertical should be greater than the spacing of each vertical support. In other words, if the vertical support is 72&#; tall, the vertical supports should not be spaced more than 72&#; apart from one another. Regardless of gate height, most cantilever gate designs do not exceed 72&#; spacing for vertical supports.

To improve the cantilever gate&#;s ability to support longer and heavier gate frames, the vertical supports can be moved closer together, forming more of a rectangle with the long side vertical versus a square. This shifts the stress on the diagonal truss from a cantilevered load where the diagonal truss will simply bend to relying almost entirely on the tensile strength.

Weight and Gate Hardware

Most cantilever gate hardware for both enclosed aluminum track gates and steel tubular external roller gates are designed to safely support gates up to 2,000 pounds for continuous duty. Cantilever gate hardware for gates in excess of 2,000 pounds is considered non-typical and is not readily available.

Gate designers should be aware that most heavy-duty gate uses either a ground mounted truck assembly or an overhead trolley system. Both of these designs will cause significant re-design of a standard cantilever gate.

Resist the temptation to simply add more rollers and gate support posts in an effort to support larger cantilever gate openings. Cantilever gates are designed to allow the loading of the cantilevered section of the gate to occur evenly between two fixed points: the respective trucks and gate support posts. This spreads the load over a wide area. Placing intermediate additional support posts and rollers may cause the load to be more concentrated on a smaller area, thus placing more resistance against the rollers and potentially causing the gate frame to fail.

Cantilever Gate Type

  • Steel Cantilever Gates &#; Use round tubular profiles in the design of the gate.
    • The top and bottom horizontal members are a 2 ½&#; O.D. tube that runs the length of the gate. This tube serves both as a structural support and as the gates top and bottom tracks. The rollers run on the outside of these tracks.
    • In-between the vertical members are the diagonal supports. On steel cantilever gates, these are typically 1 5/8&#; O.D. tubing, however, cable may be substituted.
    • The vertical gate members are 2&#; O.D. tube that are spaced no greater than 72&#; apart.
  • Aluminum Cantilever Gates &#; Use extruded aluminum square and rectangular profiles in the design of the gate.
    • In-between the vertical members are the diagonal supports that can be either a 2&#; square aluminum or cable system.
    • The top horizontal member is a custom extruded track and structural member(s) combination. The track is approximately 2 ½&#; wide by 2 ¾&#; tall. The trucks (or rollers) run inside the track. The trucks are supported from the bottom of the track and not hung from the top. This prevents water and debris from settling in the track.
    • The vertical gate members are 2&#; x 2&#; spaced no greater than 72&#; apart.
    • The bottom horizontal member is a 2&#; x 2&#; square (or 5&#; x 2&#; rectangle for larger gate openings). Not only does this member provide structural support for the gate but it also serves as the bottom guide.

Steel vs Aluminum

Steel cantilever gates are more economical and often easier to repair. The rollers and gate hardware are also very heavy-duty. Aluminum cantilever gates&#;the more expensive option&#;offer more design options:

  • Aluminum cantilever gates are an excellent choice with larger openings as the overall width of the upper and lower horizontal members may be easily extended without interfering with the track design. You can simply add additional structural supports or add a double track to the gate design.
  • Box cantilever gates are almost exclusively manufactured from aluminum. The square profiles make it easy to join with other profiles creating a series of trusses, whereas a steel tubular design requires a considerable amount of coping. Most important, aluminum is stronger than steel pound for pound. This is important when the weight of the gate is what you are trying to support with the design.
  • With the enclosed track system and square profiles, aluminum track cantilever gates are the best choice for ornamental and decorative gate designs. The square pickets may be placed between the top and bottom members or mounted on the face. The track may be positioned on the inside of the facility thus hiding it and the hardware from the outside, providing curb appeal.

Automation

Both aluminum and steel are excellent choices for automated gates. Aluminum cantilever gates will provide for more consistent travel in the overall travel of the gate as the enclosed track and truck system has tighter tolerances. Aluminum gates are lighter. If you have a very large opening or a very heavy gate by design, you may want to consider an aluminum design as it may require a smaller gate operator or place less stress on the gate operator. With openings under 27&#; and typical chain link infill, a steel cantilever gate is an excellent and economical choice.

Our Guide to Types of Metal Driveway Gates

An automatic driveway or estate gate is a fabulous addition to any property. It provides an extra layer of home security, enhances curb appeal, and increases overall property value.

When shopping for a new driveway gate, you typically start by choosing a material. Here&#;s what you should know about the various types of metal used for automatic gates to help you make the right choice for your property!

Metal Gate Materials

There are four types of materials are used to craft metal driveway gates:

  • Steel. An alloy of iron and carbon, steel is stronger than pure iron and more resistant to impact. Steel is the most heavy-duty option.
  • Aluminum. This metal is lightweight and malleable. It&#;s also entirely rust-proof. However, it&#;s less robust than steel.
  • Wrought iron. Iron that&#;s been heated and worked with tools is known as wrought iron. It&#;s more malleable than cast iron and therefore can be shaped into more intricate designs. Moreover, its fibrous appearance lends the metal a great deal of character.
  • Cast iron. Iron that&#;s been melted, poured into a mould, and left to solidify is known as cast iron. It&#;s a strong metal, but isn&#;t quite as heavy-duty as wrought iron, nor is it as ductile. In terms of appearance, it has a smoother finish than wrought iron.

Comparing the Different Metals

The four metals used for driveway gates each have their pros and cons. Here&#;s a look at how they stack up.

  • Strength and durability
    Steel is the strongest metal of the bunch and aluminum the least heavy-duty. This means that, in theory, a steel gate is best able to withstand abuse as well as the leverage forces associated with gate operation. Iron gates are only slightly less robust than steel gates.

    Although aluminum gates are the least heavy-duty, they&#;re far from being flimsy and most will hold up to anything you or Mother Nature throws its way. However, it should be noted that, unlike steel and iron gates, aluminum gates are usually not a single welded piece. Instead, the pickets are screwed in. They may, as a result, loosen over time and require adjustments. Fully-welded constructions are always more robust.
  • Maintenance
    All metal gates are low maintenance and require minimal upkeep by the user. Aluminum has the advantage of being a naturally rust-resistant material. However, iron and steel gates are finished with a powder coating to ensure that they don&#;t rust, peel, or fade.
  • Weight
    Aluminum fences are about 2.5 times lighter than steel and iron gates. This makes them less heavy-duty but, by the same token, they don&#;t require as much support. They can therefore be automated with a less powerful gate operator. Moreover, aluminum can be a practical choice for very large gates so that they can be opened and closed with greater ease.
  • Appearance
    Provided they&#;re well-made, metal gates are intrinsically elegant, whether they&#;re made of steel, iron, or aluminum. If you&#;re looking for a more ornate appearance, wrought iron is an ideal option. If simplicity is your thing, a flat-top steel, cast iron, or aluminum gate may be right for you.

Designs & Styles of Metal Gates

Metal gates generally have one of three designs:

  • Flat-top. This is the simplest gate style. The upper rail of a flat-top gate is completely straight, giving the gate a perfectly rectangular shape.

  • Arched-top. The upper rail of an arched-top gate forms a gradual, sweeping arch. This metal gate style has an elegant, traditional look and is ideal for double swing gates.
  • Arched-top with finials. This style of gate differs from the arched-top design in that the tops of the pickets (the finials) extend past the upper rail, providing a more ornamental finish.

While these are the three basic styles, there are many ways to further customize a gate. For example, you can choose the spacing between the pickets, decide the height at which the gate sits off the ground, and choose between a variety of ornamental designs for the pickets and finials.

Gate Opening Action &#; Swing or Slide?

Swinging gates are the most popular choice. They have the advantage of requiring less space alongside the driveway than a sliding gate. Moreover, swing gates are the best match for a traditional arched-top gate design. Single and double swinging gates are available. Double swinging gates have a more traditional look and are ideal for larger openings, but they do require two gate operators. Single swinging gates are the better option for smaller openings.

A traditional slide gate glides along a track and stows alongside the fence. Trackless cantilever gates, which slide along post-mounted rollers, are also available. Another option is a telescopic, or stacker gate, which consists of two or more panels that stack on top of each other when the gate opens, allowing the gate to be compactly stowed.

Top-Quality Automatic Metal Gates in Western Canada

Creative Door Services&#; provides custom residential gate systems throughout Western Canada. We source all types of metal driveway gates and provide reliable installation and maintenance services. To request a quote for a gate system, contact us at one of our locations in Vancouver, British Columbia; Kelowna, British Columbia; Edmonton, Alberta; Fort McMurray, Alberta; Calgary, Alberta; Saskatoon, Saskatchewan; Regina, Saskatchewan; and Winnipeg, Manitoba.

If you are looking for more details, kindly visit wrought iron garden fence.

Comments

0 of 2000 characters used

All Comments (0)
Get in Touch

Copyright © 2020 Wordblogger.net

  |   Minerals & Metallurgy   |   Toys & Hobbies   |   Timepieces, Jewelry, Eyewear   |   Textiles & Leather Products   |   Telecommunications   |   Shoes & Accessories   |   Service Equipment   |   Security & Protection   |   Rubber & Plastics